Wet-Look or Matte
Wet-look deepens the paver color and adds shine, popular on pool decks and driveways that get shown off. Matte keeps a more natural look and shows less around pool splash and bare feet.
Brevard County localMelbourne to Titusville — we work where we live
Built to spec, not to priceBase and edge detail done right the first time
Free written estimatesItemized, so you can compare it honestly
Rated 4.9 on GoogleRead our Google reviews
Paver cleaning & sealing in Cocoa Beach
Cleaning and sealing in Cocoa Beach, without the shortcuts.
Salt air sits on everything near the water in Cocoa Beach, and it works on paver surfaces the same way it works on a car left outside — slowly, and worse without protection. Pool decks and driveways here also take heavy UV exposure most of the year. Sealing gives the surface a layer to absorb that instead of the paver itself, and it's the difference between a deck that still looks good for a rental listing photo and one that looks tired and chalky a couple seasons in.
UV and salt air are the two things working against a paver surface here, and sealing addresses both — UV-resistant sealers slow the fading, and a sealed surface sheds salt residue instead of absorbing it. We can do wet-look for a deeper, glossier finish, or matte for a more natural look that hides pool splash better. Either way the surface has to be clean and dry before we seal — trapped moisture under a fresh seal coat causes cloudiness. Plan on resealing roughly every two to three years out here.
What that looks like here
Cocoa Beach work, specifically.
Salt Residue Barrier
A sealed surface sheds salt film instead of letting it sit and work into the paver and the joints, which matters more here than almost anywhere else in the county.
Clean, Dry, Then Sealed
We won't seal over a damp or dirty surface — trapped moisture under a fresh seal coat is what causes cloudiness. We check the surface is fully dry before we start, even if that means waiting a day.
By the numbers
Cocoa Beach homes, by the numbers.
The Brevard County tax roll counts 3,065 single-family homes in Cocoa Beach. The typical one was built in 1963, and about 89% were built before 2000.
With most homes here past twenty-five years old, a lot of the pavers and slabs have decades of sun and rain on them. That usually means cleaning and re-sanding before any sealer goes down.
Source: Florida Department of Revenue, Brevard County 2026 preliminary tax roll.
Free estimate
Start with someone walking your yard.
We'll measure, look at where the water goes, and leave you an itemized written estimate — anywhere in Cocoa Beach. No charge, no pressure.
Watch a real one
A seal job, start to finish.
Levi walks a real Brevard driveway through the whole thing — the wash, the re-sand, the seal — in under a minute. Sound on for the walkthrough.
Most of our sealing work is on pavers somebody else laid — jobs that start exactly like this one.
Get the same estimate — freeThinking of doing it yourself?
Sealing your own pavers in Cocoa Beach.
Cocoa Beach sits where salt air and humidity make the drying window the hardest part of the job. Sealer has to go down on a surface that is dry all the way through the paver and the joint sand — and beachside, morning dew, sea breeze and afternoon humidity keep pulling that window shut. The most common DIY failure here is a surface that looked dry on top while the sand underneath was still damp, which shows up a day later as milky white haze locked under the coat.
Salt also leaves a fine film a garden hose does not remove. Sealer applied over it bonds to the film rather than the paver, and that is the layer that peels first — usually along the edges that catch the most spray. Techniseal’s own instructions call for a clean, dry surface between 50°F and 85°F during application and for the 24 hours after it, with no rain in that window: beachside, that combination is the constraint, not the sealing itself.
Honest comparison
DIY versus hiring it out.
Where the two paths actually differ — and what happens when a coat goes wrong.
| Doing it yourself | Groundworks | |
|---|---|---|
| Surface prep | Rented washer, homeowner technique — the pressure that lifts old sealer is also the pressure that erodes paver faces and blows out joint sand. | Cleaning matched to the surface, plus the algae, rust and efflorescence treatment a rinse alone doesn’t touch. |
| Drying time | Judged by eye. The paver top dries hours before the joint sand underneath does. | Judged by condition and forecast — the step most often skipped, and the one most failures trace back to. |
| Temperature window | Air temperature off a phone app. | Surface temperature checked — above 90°F at the surface the bond fails, and surface runs far hotter than air. |
| Joint sand | Easy to seal before the sand is set, or to use a sand that isn’t right for the joint. | Re-sanded and set first — and after polymeric sand, manufacturers specify a 30-day wait before sealing. |
| Product choice | Whatever the store stocks — solvent and water-based, film-forming and penetrating, all sold side by side. | Chosen for the surface, its exposure, and the finish you actually want. |
| How much to buy | Estimated from the bucket’s headline coverage rate. | Calculated from the real rate — a penetrating sealer needing two mandatory coats covers roughly half what a single-coat figure suggests. |
| Application | Roller or pump sprayer, wet edge held by hand across the whole area. | Even coverage at a consistent rate, low-pressure spray, edges and adjacent surfaces masked. |
| If it goes wrong | Once cured, it has to be chemically stripped — dwell time, a second application if any re-adheres, vegetation soaked to protect it, then re-sanding — before anything can be re-applied. | Corrected by the crew that applied it. |
On a small patio with a penetrating sealer and a real dry window, doing it yourself is a reasonable project — we say so plainly in our honest DIY comparison. If a coat has already gone cloudy or started peeling, start with fixing a seal that went wrong.
Local questions
Cocoa Beach questions.
How often do pavers actually need resealing this close to the beach?
Roughly every two to three years, sometimes closer to two given the amount of sun and salt exposure a Cocoa Beach property sees. We'll look at your surface and give you a real answer instead of a generic number.
Can you seal a pool deck without making it slippery when wet?
Yes, we use sealers with slip-resistant additives made specifically for pool decks and walkways. That's a different product than what we'd use on a driveway, and we'll spec it that way for your specific job.
My pavers near the pool look faded and chalky — is that from sun or salt?
Usually both, working together. UV breaks down the sealer over time and salt air accelerates it. Sealing won't undo existing wear on its own, but a proper clean and reseal brings back most of the original color.
Keep looking around
Nearby, and next steps.
Paver cleaning & sealing nearby
More in Cocoa Beach
Fastest answer
Instant quote — give us a call.
Most questions we can answer on the phone in two minutes, and if we need to see it we'll book the walkthrough while you're on the line.
(321) 586-9227Or text a photo of the space — that's often the fastest way to get a real answer. Prefer email? [email protected].
Free estimate
Get your Cocoa Beach estimate.
Tell us what you're picturing and we'll come measure it.
Five quick questions — then you're booked in and someone reaches out within 5 minutes. Prefer to talk? Call (321) 586-9227.