Strip What's Failing First
Old sealer that's gone cloudy or peeling gets pressure-washed off, not coated over. Sealing on top of a failing layer just traps the problem — we get back to a clean surface before anything new goes down.
Brevard County localMelbourne to Titusville — we work where we live
Built to spec, not to priceBase and edge detail done right the first time
Free written estimatesItemized, so you can compare it honestly
Rated 4.9 on GoogleRead our Google reviews
Paver cleaning & sealing in Melbourne Beach
Cleaning and sealing in Melbourne Beach, without the shortcuts.
Older installations here often go years between reseals — pavers that have gone gray, lost joint sand, or picked up algae in shaded, older tree-lined stretches near the water. Cleaning and resealing brings that surface back without tearing anything out: we wash, re-sand the joints, and seal so salt air and sun start the clock over instead of finishing the job they started.
UV and salt air are the two things wearing down every sealed and unsealed surface on this coast, and on an older installation both have had years to work. We pressure-wash to strip built-up grime and old, failing sealer, then wait until the pavers are completely dry before recoating — sealing over damp pavers traps moisture underneath and causes more problems than it solves. Plan on resealing roughly every two to three years after that, sooner if the surface sits in heavy sun.
What that looks like here
Melbourne Beach work, specifically.
Wet-Look or Matte
Wet-look brings out paver color with a glossy finish; matte keeps a more natural, worn-in look that suits an older home. Both protect the surface the same way underneath — it's a look you choose, not a performance tradeoff.
On a Real Reseal Schedule
Salt air and sun break sealer down faster here than inland, so we plan on roughly every two to three years, not indefinitely. If your pavers haven't been resealed in longer than that, we'll tell you straight when we look at them.
By the numbers
Melbourne Beach homes, by the numbers.
The Brevard County tax roll counts 4,846 single-family homes in Melbourne Beach. The typical one was built in 1988, and about 77% were built before 2000.
With most homes here past twenty-five years old, a lot of the pavers and slabs have decades of sun and rain on them. That usually means cleaning and re-sanding before any sealer goes down.
Source: Florida Department of Revenue, Brevard County 2026 preliminary tax roll.
Free estimate
Start with someone walking your yard.
We'll measure, look at where the water goes, and leave you an itemized written estimate — anywhere in Melbourne Beach. No charge, no pressure.
Watch a real one
A seal job, start to finish.
Levi walks a real Brevard driveway through the whole thing — the wash, the re-sand, the seal — in under a minute. Sound on for the walkthrough.
Most of our sealing work is on pavers somebody else laid — jobs that start exactly like this one.
Get the same estimate — freeThinking of doing it yourself?
Sealing your own pavers in Melbourne Beach.
Melbourne Beach sits where salt air and humidity make the drying window the hardest part of the job. Sealer has to go down on a surface that is dry all the way through the paver and the joint sand — and beachside, morning dew, sea breeze and afternoon humidity keep pulling that window shut. The most common DIY failure here is a surface that looked dry on top while the sand underneath was still damp, which shows up a day later as milky white haze locked under the coat.
Salt also leaves a fine film a garden hose does not remove. Sealer applied over it bonds to the film rather than the paver, and that is the layer that peels first — usually along the edges that catch the most spray. Techniseal’s own instructions call for a clean, dry surface between 50°F and 85°F during application and for the 24 hours after it, with no rain in that window: beachside, that combination is the constraint, not the sealing itself.
Honest comparison
DIY versus hiring it out.
Where the two paths actually differ — and what happens when a coat goes wrong.
| Doing it yourself | Groundworks | |
|---|---|---|
| Surface prep | Rented washer, homeowner technique — the pressure that lifts old sealer is also the pressure that erodes paver faces and blows out joint sand. | Cleaning matched to the surface, plus the algae, rust and efflorescence treatment a rinse alone doesn’t touch. |
| Drying time | Judged by eye. The paver top dries hours before the joint sand underneath does. | Judged by condition and forecast — the step most often skipped, and the one most failures trace back to. |
| Temperature window | Air temperature off a phone app. | Surface temperature checked — above 90°F at the surface the bond fails, and surface runs far hotter than air. |
| Joint sand | Easy to seal before the sand is set, or to use a sand that isn’t right for the joint. | Re-sanded and set first — and after polymeric sand, manufacturers specify a 30-day wait before sealing. |
| Product choice | Whatever the store stocks — solvent and water-based, film-forming and penetrating, all sold side by side. | Chosen for the surface, its exposure, and the finish you actually want. |
| How much to buy | Estimated from the bucket’s headline coverage rate. | Calculated from the real rate — a penetrating sealer needing two mandatory coats covers roughly half what a single-coat figure suggests. |
| Application | Roller or pump sprayer, wet edge held by hand across the whole area. | Even coverage at a consistent rate, low-pressure spray, edges and adjacent surfaces masked. |
| If it goes wrong | Once cured, it has to be chemically stripped — dwell time, a second application if any re-adheres, vegetation soaked to protect it, then re-sanding — before anything can be re-applied. | Corrected by the crew that applied it. |
On a small patio with a penetrating sealer and a real dry window, doing it yourself is a reasonable project — we say so plainly in our honest DIY comparison. If a coat has already gone cloudy or started peeling, start with fixing a seal that went wrong.
Local questions
Melbourne Beach questions.
Our pavers have never been sealed — is it too late to start now?
No. We pressure-wash to get years of grime and algae off first, let the surface dry completely, then seal from there. It's more cleaning work than a paver that's been maintained on schedule, but a never-sealed patio in Melbourne Beach can still be brought back — it just takes the wash step seriously.
How do I know if my sealer has already failed?
Look for cloudy or peeling patches, color that's gone flat or gray, or joint sand that's washing out between the pavers. Any of those means the old coat isn't doing its job anymore. We'll check the surface in person and tell you honestly whether it needs a full reseal or just a wash.
Why does sealer seem to wear out faster on my patio than my neighbor's?
Sun exposure and how close the surface sits to salt air both matter — a patio in full sun near the water breaks a coat down faster than a shaded one. We look at your specific spot rather than quoting a blanket schedule for the whole property.
Keep looking around
Nearby, and next steps.
Paver cleaning & sealing nearby
More in Melbourne Beach
Fastest answer
Instant quote — give us a call.
Most questions we can answer on the phone in two minutes, and if we need to see it we'll book the walkthrough while you're on the line.
(321) 586-9227Or text a photo of the space — that's often the fastest way to get a real answer. Prefer email? [email protected].
Free estimate
Get your Melbourne Beach estimate.
Tell us what you're picturing and we'll come measure it.
Five quick questions — then you're booked in and someone reaches out within 5 minutes. Prefer to talk? Call (321) 586-9227.